Floor Heating Division of MP Global Products

QuietWarmth Float 2-in-1 Starter Kit

QuietWarmth Float 2-in-1 Starter Kit- Radiant Floor Heating System for Floating Floors (Two Mats in One!) Includes Thermostat

  • 2-in-1 system allows you to cut the mat and use both sections
  • Smart Home compatible programmable thermostat with 7-day scheduling
  • Floor heating for laminate, engineered, and floating floors
3 x 16 ft. 8 in. 120-VoltQWF3X166F120VAL 3 x 16 ft. 8 in. 240-VoltQWF3X166F240VAL

Features

 Ultra-thin, conductive ink film technology

Ultra-thin, conductive ink film technology

For floating floors including luxury vinyl and laminate hardwoods

Roll Out Installation

Roll Out Installation

Connect up to 150 sq ft of mats wired in parallel on 1 thermostat

Cut To Fit

Cut To Fit

Customize your layout by cutting the length of the mats

Factory Attached Leads

Factory Attached Leads

Factory attached 15 ft electrical leads to each mat

Fast Installation

Fast Installation

No extra mortars or mess - 30 minute installation time (based on 60 sq ft area)

12 Watts Per Sq Ft

12 Watts Per Sq Ft

Ultra low EMF

Ultra low EMF

120V/240V Available

120V/240V Available

Temperature Control

Temperature Control

Control Temperature with an available floor sensing thermostat

Energy Efficient

Energy Efficient

Up to 6¢ per hour (based on 60 sq ft and typical use)

If you are looking for a test report please send an email to [email protected] and specify the product and type of report you are needing. We would be more than happy to email you a copy of any testing data that we have.

Yes, the QuietWarmth Radiant Heating Mats can be adjusted to length by cutting in between the solid black bars, on the dotted line. You cannot alter the width of the mats. The QuietWarmth Tile mats need to be properly sealed prior to installing tile floor covering. Refer to our installation guides for complete instruction prior to installing.

You can connect multiple QuietWarmth mats by wiring them in parallel and joining them together in a junction box, then connecting the junction box to the thermostat. The 120V system can handle up to 150 square feet per dedicated circuit; the 240V system can handle up to 300 square feet per dedicated circuit. We recommend you consult with a licensed electrician and read our full installation instructions prior to beginning your installation.

The mats cannot be cut to width, nor can they have a circle cut out of them; they can only be cut to length in a straight line between the solid black conducting bars. Depending on your room dimensions, you could install separate mats along the side and in front of the toilet. If there is not enough space to install a mat on the sides of the toilet, you would install the mat only in front of the toilet.

You can connect multiple QuietWarmth mats by wiring them in parallel and joining them together in a junction box, then connecting the junction box to the thermostat. The 120V system can handle up to 150 square feet per dedicated circuit; the 240V system can handle up to 300 square feet per dedicated circuit. We recommend you consult with a licensed electrician and read our full installation instructions prior to beginning your installation.

QuietWarmth cannot be used with nail-down installations. If a mat is punctured, the function and safety would be compromised and it must be replaced.

You can install QuietWarmth mats on bathroom floors. The mats cannot be placed in the shower.

The QuietWarmth Tile system is designed to be installed under ceramic, porcelain, or natural stone tile that require a thinset or mortar installation. The QuietWarmth Float system is designed to be installed under floating floor installations.

QuietWarmth is designed as a comfort heat system, however it will provide some ambient heat. To determine whether this system will provide primary heat in your room, you would need to conduct a J-Calculation for heat loss.

The proper mat voltage is determined by the power supply in your home. Please consult with a licensed electrician for further guidance.

No, this product is approved for indoor use only.

No, this product is not designed to be installed in showers or other areas where they will frequently be directly exposed to water.

QuietWarmth Float is approved for underneath floating luxury vinyl flooring. For glue-down luxury vinyl flooring you will need to use the QuietWarmth Tile system.

Yes, you can use a cork underlayment below the QuietWarmth Float mats under a floating floor.

We would defer to your flooring manufacturer’s recommendations for suitable substrates.

The maximum temperature of the mat is 84-85 F. This system puts out 12 watts (40.94BTUs) per square foot.

When installing the QuietWarmth radiant heat system, the temperature sensor (included with the thermostat) should be adjacent to the long side of one mat, parallel to the length. It should not cross over the mat. You want to locate it roughly 6″-12″ out from the wall.  See the installation instructions for further explanation.

The QuietWarmth system is not designed to be connected to a power cord and plugged in to an outlet. Per National Electrical Code, this product needs to be wired to its own 20 amp dedicated circuit.

Reviews

Leave Reviews
by Joe - Home Depot Review

Product is easy to work with directions were well-written

Product is easy to work with directions were well-written

Where To Buy

Distributor

Click here to view distributors

Online Store

Click here to view online retailers

Find Distributor

To help find a local distributor in your area with the right inventory levels, please fill out the form below.

Become a Distributor

Hidden
Name(Required)
Address(Required)
Hidden

Find In-Store

Become a Dealer

Enhanced Content

Provides uniform heat and cost less to operate
Uniformly heats floors with no gaps without raising the flooring height. Even heat distribution allows QuietWarmth systems to cycle quicker resulting in less energy consumption. In addition, the heat will never exceed 85 degrees F to provide the perfect temperature underfoot.
  • 120V QuietWarmth mats work with 120V systems. 240V QuietWarmth mats work with 240V systems.

  • There's No Easier Radiant Floor Heating System to Install
    Simple 4-step process! 1. Install underlayment 2. Roll out electric radiant heat film 3. Hook up electric wiring 4. Install final floor covering
    Designed For

  • All Floating Floors
  • Floating Tiles
  • Laminate Flooring
  • Engineered Wood Flooring
  • Luxury Vinyl Flooring (4mm or thicker)
  • Cork and Bamboo


  • Note: Refer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation