Floor Heating Division of MP Global Products

QuietWarmth Float Heat Mats

QuietWarmth Float- Radiant Floor Heating System for Floating Floors (Laminate, Luxury Vinyl, Engineered Wood, and More!)

  • Floor heating for vinyl plank (4mm or thicker) laminate, engineered hardwood & floating floors
  • Easy to install radiant floor heating mats - cut to length
  • Keep feet warm w/cost-effective electric floor heating system
  • Available in 120V mats or 240V mats
  • Not for Use in Wet Area (Shower Floor) - ONLY for Use in Dry Area
Float 1.5' x 5' 120V7.5 sqftQWARM1.5X5F120 Float 1.5' x 10' 120V 15 sqftQWARM1.5X10F120 Float 2-in-1 1.5' x 16'8" 120V25 sqftQWARM1.5X166F120 Float 3' x 5' 120V15 sqftQWARM3X5F120 Float 3' x 10' 120V30 sqftQWARM3X10F120 Float 3' x 25' 120V75 sqftQWARM3X25F120 Float 2-in-1 3' x 16'8" 120V50 sqftQWARM3X166F120 Float 1.5' x 5' 240V7.5 sqftQWARM1.5X5F240 Float 1.5' x 10' 240V15 sqftQWARM1.5X10F240 Float 2-in-1 1.5' x 16'8" 240V25 sqftQWARM1.5X166F240 Float 3' x 5' 240V15 sqftQWARM3X5F240 Float 3' x 10' 240V30 sqftQWARM3X10F240 Float 3' x 25' 240V75 sqftQWARM3X25F240 Float 2-in-1 3' x 16'8" 240V50 sqftQWARM3X166F240

Features

 Ultra-thin, conductive ink film technology

Ultra-thin, conductive ink film technology

For floating floors including luxury vinyl and laminate hardwoods

Easy Installation

Easy Installation

Roll out mats, wire in parallel to junction box or thermostat, and install your flooring the same day!

Cut To Fit

Cut To Fit

Customize your layout by cutting the length of the mats.

Factory Attached Leads

Factory Attached Leads

Factory attached 15 ft electrical leads to each mat

120V/240V Available

120V/240V Available

Connect up to 120 sq ft of 120V mats per dedicated circuit Connect up to 240 sq ft of 240V mats per dedicated circuit

Energy Efficient

Energy Efficient

Up to 6¢ per hour (based on 60 sq ft and typical use)

12 Watts Per Sq Ft

12 Watts Per Sq Ft

UL Listed for Safety

UL Listed for Safety

Temperature Control

Temperature Control

Control Temperature with an available floor sensing thermostat

Ultra low EMF

Ultra low EMF

If you are looking for a test report please send an email to [email protected] and specify the product and type of report you are needing. We would be more than happy to email you a copy of any testing data that we have.

Yes, the QuietWarmth Radiant Heating Mats can be adjusted to length by cutting in between the solid black bars, on the dotted line. You cannot alter the width of the mats. The QuietWarmth Tile mats need to be properly sealed prior to installing tile floor covering. Refer to our installation guides for complete instruction prior to installing.

You can connect multiple QuietWarmth mats by wiring them in parallel and joining them together in a junction box, then connecting the junction box to the thermostat. The 120V system can handle up to 150 square feet per dedicated circuit; the 240V system can handle up to 300 square feet per dedicated circuit. We recommend you consult with a licensed electrician and read our full installation instructions prior to beginning your installation.

The mats cannot be cut to width, nor can they have a circle cut out of them; they can only be cut to length in a straight line between the solid black conducting bars. Depending on your room dimensions, you could install separate mats along the side and in front of the toilet. If there is not enough space to install a mat on the sides of the toilet, you would install the mat only in front of the toilet.

You can connect multiple QuietWarmth mats by wiring them in parallel and joining them together in a junction box, then connecting the junction box to the thermostat. The 120V system can handle up to 150 square feet per dedicated circuit; the 240V system can handle up to 300 square feet per dedicated circuit. We recommend you consult with a licensed electrician and read our full installation instructions prior to beginning your installation.

Yes, the QuietWarmth Radiant Heating Mats can be adjusted to length by cutting in between the solid black bars, on the dotted line. You cannot alter the width of the mats. The QuietWarmth Tile mats need to be properly sealed prior to installing tile floor covering. Refer to our installation guides for complete instruction prior to installing.

QuietWarmth cannot be used with nail-down installations. If a mat is punctured, the function and safety would be compromised and it must be replaced.

The cut portion of the QuietWarmth Float and QuietWarmth Tile mats are not reusable and should be discarded. Our QuietWarmth 2-in-1 Float Mats have lead wires on both ends, so you are able to use both ends of the cut mat.

You can install QuietWarmth mats on bathroom floors. The mats cannot be placed in the shower.

The QuietWarmth Tile system is designed to be installed under ceramic, porcelain, or natural stone tile that require a thinset or mortar installation. The QuietWarmth Float system is designed to be installed under floating floor installations.

QuietWarmth is designed as a comfort heat system, however it will provide some ambient heat. To determine whether this system will provide primary heat in your room, you would need to conduct a J-Calculation for heat loss.

The proper mat voltage is determined by the power supply in your home. Please consult with a licensed electrician for further guidance.

No, this product is approved for indoor use only.

No, this product is not designed to be installed in showers or other areas where they will frequently be directly exposed to water.

QuietWarmth Float is approved for underneath floating luxury vinyl flooring. For glue-down luxury vinyl flooring you will need to use the QuietWarmth Tile system.

Yes, you can use a cork underlayment below the QuietWarmth Float mats under a floating floor.

We would defer to your flooring manufacturer’s recommendations for suitable substrates.

QuietWarmth can be installed throughout the entire room. The only restrictions regarding furniture is it must not sit flush to the floor. Proper air flow is imperative to ensure there is not excessive heat build up, that could potentially damage your flooring. 

QuietWarmth Float is approved to go under a floating floor that exceeds 4mm in overall thickness. Please ensure your flooring is approved for use with radiant heat systems.

QuietWarmth is not approved for exterior use.

The maximum temperature of the mat is 84-85 F. This system puts out 12 watts (40.94BTUs) per square foot.

QuietWarmth Float is approved for use under floating laminate floors.

When installing the QuietWarmth radiant heat system, the temperature sensor (included with the thermostat) should be adjacent to the long side of one mat, parallel to the length. It should not cross over the mat. You want to locate it roughly 6″-12″ out from the wall.  See the installation instructions for further explanation.

The QuietWarmth system is not designed to be connected to a power cord and plugged in to an outlet. Per National Electrical Code, this product needs to be wired to its own 20 amp dedicated circuit.

Reviews

Leave Reviews
by Lollapaloozies - Home Depot Review

I used three 3'×10' mats to heat a 12'×12' outbuilding....

I used three 3’×10′ mats to heat a 12’×12′ outbuilding. I researched my options and found this system to not only be affordable but the operating cost will pay for them in less than two months. Electric Space heaters cost $.25/hr ($6/day or $180/month) to operate. This floor heating costs $.50-$1.50.
by thomas - Lowe's Review

Great solution for laminate

Installed in a remodeled walk in closet that’s over the garage and a little chilly in the winter. Great Youtube videos to help with the install. I installed one 3 ft wide and one 1.5 ft wide strip to keep the current draw down. The 10 ft long 3 ft wide strip draws 2.78 A and the 1.5 ft strip draws 1.3 A. For supplemental heat it seems to work great!

by Hadlejer - Amazon Review

Easy to install

Where To Buy

Distributor

Click here to view distributors

Online Store

Click here to view online retailers

Find Distributor

To help find a local distributor in your area with the right inventory levels, please fill out the form below.

Become a Distributor

Hidden
Name(Required)
Address(Required)
Hidden

Find In-Store

Become a Dealer

Online Stores

Enhanced Content

Provides uniform heat and cost less to operate
Your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly throughout the room. Even heat distribution allows the QuietWarmth systems to cycle quicker resulting in less energy consumption. Also, the heat will never exceed 85 degree F, allowing your feet to have the perfect temperature.
  • 120V QuietWarmth mats work with 120V systems. 240V QuietWarmth mats work with 240V systems
There is no easier radiant floor heating system to install
Simple 4-step process!
  • 1. Install underlayment
  • 2. Roll out electric radiant heat film
  • 3. Hook up electric wiring
  • 4. Install final floor covering
Floor Covering Materials
  • All Floating Floors
  • Floating Tiles
  • Laminate Flooring
  • Engineered Wood Flooring
  • Luxury Vinyl Flooring (4mm or thicker)
  • Cork and Bamboo
Note: Refer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation